Magneto replacement - EIS-41000



           What is the future of magneto ?   Electroair introduce Electronic Ignition Kit that is 10 % to 15% fuel efficient.  EIS-41000 Lycoming                4 cylinder Electronic Ignition Kit Direct Drive             ( non-impulse coupled ) Magneto Replacement
       The EIS-41000 Electronic Ignition Kit is a fully STC'd kit for most Lycoming 4cyl engines. Replacing one magneto with the EIS-41000 will typically improve fuel economy on average by 10-15% (many operators have reported consistent fuel savings of 1gph or greater). Additionally, there will be an improvement in horsepower, smoother engine operation, and improved high altitude performance. The EIS-41000 adjusts spark timing automatically by way of our MAP Sensor - timing is adjusted with altitude. Most parts on the EIS-41000 are not life limited (the MTH is recommended to be changed at overhaul of the engine; spark plug wires on a regular interval) - this combined with reduced spark plug fouling means lower maintenance costs. This kit can be used on either 12V or 24V systems.
          Kit includes: all the required parts to replace the direct drive magneto (typically, the right hand mag) in most 4cyl Lycoming engines. (Please refer to the eligibility schedule to verify the system can be installed on your engine - Note: engines are being added regularly).

Please leave comments and share.

Comments

Post a Comment

Popular posts from this blog

Cessna 152 Magneto Check

MAGNETO CHECK. NEVER ADVANCE TIMING BEYOND SPECIFICATIONS IN ORDER TO REDUCE RPM DROP. Too much importance is being attached to RPM drop in single ignition. RPM drop on single ignition is a natural characteristic of dual ignition design. The purpose of the following magneto check is to determine that all cylinders are firing. If all cylinders are not firing, the engine will run extremely rough and cause for investigation will be quite apparent. The amount of RPM drop is not necessarily significant and will be influenced by ambient air temperature, humidity, airport altitude, etc. In fact, absence of RPM drop should be cause for suspicion that the magneto timing has been bumped up and is set in advance of the setting specified. Magneto checks should be performed on a comparative basis between individual right and left magneto performance. a. Start and run engine until the oil and cylinder head temperatures are in normal operating ranges. b. Advance engine speed to 1700 RPM. c. Tu
Read more

Brake System Cessna 172

                             BRAKE SYSTEM -MAINTENANCE PRACTICES              1. Description and Operation A. The hydraulic brake system is comprised of two master cylinders, located immediately forward of the  pilot’s rudder pedals, brake lines and hoses, and single-disc, floating cylinder brake assemblies located at  each main landing gear wheel. B. The parking brake system is comprised of a pull-type handle and mechanical connections which are  linked to the rudder pedal assembly. Pulling aft on the brake handle applies mechanical pressure to the  rudder pedals, activating the brakes and locks the handle in place. Turning the handle 90 degrees will  release the parking brake and allow for normal operation through the rudder pedals. C. Brake operation is accomplished by pushing on the upper part of each rudder pedal. This motion is  mechanically transmitted to the respective brake master cylinder, and through fluid-carrying lines out to  the brake assembly where fluid pressure
Read more

McCauley Propeller Installation fixed pitch

Image
Propeller Installation for all fixed pitch propellers (except 1A162 model propellers).                   WARNING: MAKE SURE THE MAGNETO IS GROUNDED BEFORE INSTALLING  THE PROPELLER OR CONNECTING EXTERNAL POWER.                NOTE: McCauley recommends that propeller mounting nuts (if applicable) be replaced at each  propeller installation, whenever possible. However, nuts may be reused providing the threads are in good condition and the locking material prevents turning of the nut on the  stud by hand. Propeller mounting bolts must be magnetic particle inspected in accordance  with ASTM E-1444 or replaced whenever the propeller is removed from the engine.                NOTE: The aircraft maintenance manual or STC installation instructions should always be  consulted for any specialized procedures applicable to a specific aircraft. Various spinner arrangements not manufactured by McCauley may be used which require additional procedures. (1) Make sure the mating surfaces of t
Read more