CAR - 147 APPROVED MAINTENANCE TRAINING ORGANISATION

     CAR - 147 APPROVED MAINTENANCE TRAINING ORGANISATION (TYPE TRAINING)
Issue 1, Revision 0 19th September, 2014
                      Rule 133B of the Aircraft rule 1937 stipulates that organizations engaged in the
Aircraft type training shall be approved. Subsequent to the release of CAR 66, on 1st Dec 2011, it was essential to harmonize training requirements for type training organizations to international standards. CAR 147 is based on EASA part 147.
                    CAR-147 specifies the requirements to be met by organizations seeking approval
to conduct type training and examination as specified in CAR 66. The CAR 147 specifies conditions for issue, renewal, suspension and revocation of certificates attached to the approval and privileges thereof.
                 This CAR provides the technical standards and guidelines for the approval of aircraft maintenance type training organizations. CAR 147 for type training organizations is issued under the provision of Rule 133A, Aircraft Rules 1937 and shall be applicable from 2nd October, 2014.
              The CAR 147 provides the common technical standards and guidelines to conduct recognized type training courses, to conduct examinations and to issue training certificates with effective from 2nd October, 2014. The existing approval for type training organizations will be valid till 31st December 2014. Subsequent to which CAR 147 approval shall have to be
sought by the operators. However after release of this CAR approval also can be sought if operator desires so.
                CAR-147 specifies the requirements to be met by organizations seeking approval to conduct type training and examination as specified in CAR 66. The CAR 147 specifies conditions for issue, renewal, suspension and revocation of certificates attached to the approval and privileges thereof.

Comments

Post a Comment

Popular posts from this blog

Cessna 152 Magneto Check

MAGNETO CHECK. NEVER ADVANCE TIMING BEYOND SPECIFICATIONS IN ORDER TO REDUCE RPM DROP. Too much importance is being attached to RPM drop in single ignition. RPM drop on single ignition is a natural characteristic of dual ignition design. The purpose of the following magneto check is to determine that all cylinders are firing. If all cylinders are not firing, the engine will run extremely rough and cause for investigation will be quite apparent. The amount of RPM drop is not necessarily significant and will be influenced by ambient air temperature, humidity, airport altitude, etc. In fact, absence of RPM drop should be cause for suspicion that the magneto timing has been bumped up and is set in advance of the setting specified. Magneto checks should be performed on a comparative basis between individual right and left magneto performance. a. Start and run engine until the oil and cylinder head temperatures are in normal operating ranges. b. Advance engine speed to 1700 RPM. c. Tu...
Read more

Brake System Cessna 172

                             BRAKE SYSTEM -MAINTENANCE PRACTICES              1. Description and Operation A. The hydraulic brake system is comprised of two master cylinders, located immediately forward of the  pilot’s rudder pedals, brake lines and hoses, and single-disc, floating cylinder brake assemblies located at  each main landing gear wheel. B. The parking brake system is comprised of a pull-type handle and mechanical connections which are  linked to the rudder pedal assembly. Pulling aft on the brake handle applies mechanical pressure to the  rudder pedals, activating the brakes and locks the handle in place. Turning the handle 90 degrees will  release the parking brake and allow for normal operation through the rudder pedals. C. Brake operation is accomplished by pushing on the upper part of each rudder pedal. This motion i...
Read more

McCauley Propeller Installation fixed pitch

Image
Propeller Installation for all fixed pitch propellers (except 1A162 model propellers).                   WARNING: MAKE SURE THE MAGNETO IS GROUNDED BEFORE INSTALLING  THE PROPELLER OR CONNECTING EXTERNAL POWER.                NOTE: McCauley recommends that propeller mounting nuts (if applicable) be replaced at each  propeller installation, whenever possible. However, nuts may be reused providing the threads are in good condition and the locking material prevents turning of the nut on the  stud by hand. Propeller mounting bolts must be magnetic particle inspected in accordance  with ASTM E-1444 or replaced whenever the propeller is removed from the engine.                NOTE: The aircraft maintenance manual or STC installation instructions should always be  consulted for any specialized procedures applicable to a specific aircraft....
Read more