AAC04-2017

 AAC04-2017 explains the procedures for  OJT to   to meet the criteria for the issue of licence. 
  “CAR-66 Aircraft Maintenance Engineer’s Licence Guidance Document” attached as Appendix-A explains the requirements for obtaining CAR 66 AMEL, procedures for documentation of OJT tasks and maintenance of OJT records.
  OJT - be approved by the DGCA and it required to be conducted at and under the control of a maintenance organisation appropriately approved for the maintenance of the particular aircraft type and to be assessed by appropriately qualified and designated assessors.
  Documentation - AMO should detail the procedures in  MOE which should address the following:-
       a) procedures for on-the job training as per Section 6 of Appendix-III to CAR 66;
       a) competence assessment of personnel; 
       b) procedure for the issue of the recommendation to DGCA for the issue of a CAR 66 licence;
       c) Qualification and experience requirement of OJT Supervisor and Assessors;
       d) Procedures for documentation of OJT.
 OJT Supervisor –  qualification and experience 
       a) Type rated AME holding full scope authorization in applicable category (B1/B2) on applicable aircraft. 
       b) Minimum 3 years of maintenance certification experience on applicable family of aircraft. 
       c) Should be competent to perform the function. 
  OJT Assessors :- qualification 
       a) Type rated AME holding full scope authorization in applicable cat (B1/B2) on applicable aircraft. 
       b) Minimum 5 years of maintenance certification experience on applicable family of aircraft. 
      c) competent to perform the function. 
 SPSINGHAME.COM

Comments

Post a Comment

Popular posts from this blog

Cessna 152 Magneto Check

MAGNETO CHECK. NEVER ADVANCE TIMING BEYOND SPECIFICATIONS IN ORDER TO REDUCE RPM DROP. Too much importance is being attached to RPM drop in single ignition. RPM drop on single ignition is a natural characteristic of dual ignition design. The purpose of the following magneto check is to determine that all cylinders are firing. If all cylinders are not firing, the engine will run extremely rough and cause for investigation will be quite apparent. The amount of RPM drop is not necessarily significant and will be influenced by ambient air temperature, humidity, airport altitude, etc. In fact, absence of RPM drop should be cause for suspicion that the magneto timing has been bumped up and is set in advance of the setting specified. Magneto checks should be performed on a comparative basis between individual right and left magneto performance. a. Start and run engine until the oil and cylinder head temperatures are in normal operating ranges. b. Advance engine speed to 1700 RPM. c. Tu...
Read more

Brake System Cessna 172

                             BRAKE SYSTEM -MAINTENANCE PRACTICES              1. Description and Operation A. The hydraulic brake system is comprised of two master cylinders, located immediately forward of the  pilot’s rudder pedals, brake lines and hoses, and single-disc, floating cylinder brake assemblies located at  each main landing gear wheel. B. The parking brake system is comprised of a pull-type handle and mechanical connections which are  linked to the rudder pedal assembly. Pulling aft on the brake handle applies mechanical pressure to the  rudder pedals, activating the brakes and locks the handle in place. Turning the handle 90 degrees will  release the parking brake and allow for normal operation through the rudder pedals. C. Brake operation is accomplished by pushing on the upper part of each rudder pedal. This motion i...
Read more

McCauley Propeller Installation fixed pitch

Image
Propeller Installation for all fixed pitch propellers (except 1A162 model propellers).                   WARNING: MAKE SURE THE MAGNETO IS GROUNDED BEFORE INSTALLING  THE PROPELLER OR CONNECTING EXTERNAL POWER.                NOTE: McCauley recommends that propeller mounting nuts (if applicable) be replaced at each  propeller installation, whenever possible. However, nuts may be reused providing the threads are in good condition and the locking material prevents turning of the nut on the  stud by hand. Propeller mounting bolts must be magnetic particle inspected in accordance  with ASTM E-1444 or replaced whenever the propeller is removed from the engine.                NOTE: The aircraft maintenance manual or STC installation instructions should always be  consulted for any specialized procedures applicable to a specific aircraft....
Read more